Jan
21
2009

Basic 220 Volt Circuits

220 volt circuits (AKA 230 volt, or 240 volt) are used to supply power to appliances which draw high currents such as clothes dryers, ranges, ovens, cook-tops, heaters, air conditioners, rotary phase converters, and water heaters.

This article is for informational purposes only, and it may be entirely or partly incorrect.  Electrical work should only be performed by qualified persons. Anyone who does electrical work must always follow all safety rules and guidelines. Read the Safety Rules for Electrical work before going any further.  By continuing you agree that you are responsible for your own actions.

Parts of a 220 Circuit
No matter what appliance you are wiring for, any 220 circuit has three elements:

  • 1) The breaker panel connections.
  • 2) The supply wire.
  • 3) The terminal connection, which can be either a special receptacle or a direct connection to an appliance.
  • Disconnects
    For any appliances rated over 300 Volt-Amps (which includes almost everything 220) there must be either a means of disconnect at the appliance or a breaker lock permanently installed in the panel so that a service man can insure his own safety. (NEC article 422.31) “Means of disconnect” can include a pigtail which can be unplugged from a receptacle, a disconnect device (often used for HVAC equipment) or a unit mounted switch which has a clearly labeled off position. Appliances which are in a direct line of site of and in the same room as the breaker panel are exempt from this requirement.

    Any time that you are working with aluminum wire, you must coat all connections with conductive grease such as Ideal brand Noalox. Failure to do so will result in a connection failure due to corrosion, and a hazardous condition which could result in fire or electrical shock.

    Breaker Panel Connections
    Important safety note: Main panels cannot usually be de-energized by turning off breakers. Only qualified personnel should work on main electrical panels. A simple mistake can result in death or injury.

    All 220 circuits connect to the breaker panel through a double pole breaker (or equivalent fuse). Double pole breakers often look like a pair of single pole breakers that are stuck together – because that is exactly what they are. 220 equipment will actually function if it is connected by way of two single pole breakers, but it wouldn’t be safe or up to code, because in the event of a fault one breaker might trip causing the appliance to stop working, but it would still be energized by the other breaker. So double pole breakers are designed to trip both sides simultaneously. The amp ratings of breakers should never exceed the amp rating of either the wire, appliance, receptacle, or disconnect used in the circuit.

    Power Connections
    The 2 line voltage wires which are feeding the 220 circuit connect to the double pole breaker in the panel. Both of these wires should be either black or red for their entire exposed length inside of the breaker panel. These wires can be colored with paint, tape, or perm marker to comply with this code.

    Ground and Neutral Connections
    All modern 220 circuits will also have a ground wire which is identified by either green insulation or by being bare metal with no insulation. The ground wire connects to the ground bar. Some 220 circuits will also have a white insulated neutral wire which connects to the neutral bar, or to the combined neutral / ground bar.

    Wire for 220 Circuits
    The wire requirements for 220 volt circuits are pretty much the same as for any other circuit – it must be of the proper type for the place that it is being used, it must have sufficient volt – amp capacity, and it must have the correct number of conductors. Proper color coding would also be nice, but isn’t a big deal because the exposed lengths of the conductors (in the main panel and in the terminal device) can be colored with paint, tape, or permanent marker. If you are wiring for a dryer, range, or any other 220-110 combo appliance you must use a four conductor wire with an insulated neutral and a separate ground such as X-3-WG. If you are wiring for straight 220 equipment such as a water heater then you can use a three conductor wire such as X-2-WG. The amp rating of the wire should never be less than that of the circuit breaker that is used. You can find a handy wire application / amp rating chart on this page.

    Note: You can no longer install 3 wire range or dryer circuits – you must install 4 wire systems for ranges and dryers. If you already have a 3 wire range or dryer then don’t worry, your old appliance can be made compatible with a 4 wire system by installing a 4 wire pigtail on it. Then when you buy a new appliance it will plug right in to your new 4 wire system.

    The wiring inside of a modern 4 wire stove receptacle

    The wiring inside of a modern 4 wire stove receptacle

    Terminal Connections
    Connecting the terminal connections on a 220 system aren’t all that different than installing any other appliance, fixture or receptacle except that the wire and connection hardware is usually bigger (and a little bit harder to work with) and there is an extra “hot” wire. Because of the bigger stiffer wire it is also more important to cut the conductors to the correct length as you won’t be able to stuff extra wire into a box like you can with most fixtures.

    A Frequently asked Question
    Why do some 220 circuits have a neutral wire and others don’t?  Because some appliances contain 110 volt internal circuits (such as timers and electronic displays) which require a neutral connection to comply with current codes. When these 4 wire appliances are connected to old 3 wire systems via a 3 wire pigtail they use the ground conductor for the neutral.  Other “straight” 220 appliances such as water heaters have no need for a neutral because the current both feeds and returns by way of the two hot wires as the current polarity alternates.  Ideally, in any circuit the ground wire serves only as a safety feature and never carries any current under normal circumstances.

    Related Articles:

    Understanding 220 Circuits

    Written by David LaFerney in: Electrical Wiring |

    4 Comments »

    • Jim K says:

      I just bought a mobile home. The people around here say that the people who were here before me wanted to fix this place up, but didn’t know how to complete it. I feel they got over whelmed and gave up after starting.

      I broke up with my ex after 13 yrs. so this was a good place for me because it was extremely cheap. This place was made in 1967, and the people before me removed everything from the carpet to the kitchen sink. They did however put in new wiring including a 240 volt service, took down all the paneling and nailed up dry wall.

      The 240 volt cable that they ran is about 3ft. too short of where it’s supposed to go. I still needed to hook up the four wires inside the cable to the outlet so I could plug in my dryer. With your help on the colors of the wires it now works. I still have to buy a longer 240 volt cable but my dryer now does work.

      Thank You!

    • Mike Buchan says:

      I need some assistance! And how to ask is one of the problems. As an American living in old Russia and need to do some small repairs to the house wiring and install a couple of new wall plugs.
      In the kitchen I have a standard light switch and just wanted to add a couple of plugs. Nothing worked at all. If the light was on, the plugs were off. as I thought about the problem and looked at it from a different view — I discovered another older light switch behind the wall cupboard!
      I have taken apart all my wiring and the ‘new’ light switch works fine. I tried connecting a wire to the ‘old’ switch and the same failure happened — light on, plug power off.
      Fortunately most of the wiring (and plumbing) is on the outside of the concrete and brick interior walls so access is no problem.
      To get power to these plugs 100% of the time, do I need to connect the wire to the new plugs before the ‘old’ switch — directly to the main power line into the kitchen.
      Oh, BTW this house is about 50 years old and 220 volts.
      Please reply by email, Thanks!

      Mike

      • David LaFerney says:

        Mike,

        As much as I would like to I’m afraid that I can’t really be much help with this. Furthermore I would highly recommend that you hire a local electrician to help you sort it all out. Electricity works the same no matter where you are, but local methods have to be taken into account.

    • pretty rings says:

      Hi there, after reading this amazing article i am as well delighted to share my
      know-how here with friends.

    RSS feed for comments on this post. TrackBack URL


    Leave a Reply

    Powered by WordPress. Theme: TheBuckmaker. Darlehen, Bauplan